Overview

Angel eye headlights - a lamp.     
Angel eyes headlights refers to the high beam head light and outside near the yellow or other colors around the ring formed by the LED lights, under lights in the show is pretty wide. BMW 5 Series headlight from the initial design, when you open headlights, the BMW will have a large halo of light, the halo halo like an angel's head, so many users give her a nickname from the: name is angel eyes. Under normal circumstances, the original "angel eyes" headlights are with the lens cap and xenon headlamps. Remove the beautiful "angel eyes" headlights no other practical functions. Now factory-installed "angel eyes" headlights in the BMW series of mainly primary, general vehicle upgrades "angel eyes" headlights can be installed through the purchase of foreign tuning the production of "Angel eyes" headlight assembly to achieve, the current the mass of cars of the "angel eyes" assembly range, most of the German manufacturers, process excellent, the price is relatively high. Taiwan angel eyes headlights in the appearance requirements of the good, beautiful appearance, and has a dynamic, but this lamp factory to write very clearly prohibiting the installation of xenon light, but there are a lot of people to force the addition of xenon. according to the angle of the light small and the filter lens on the xenon is also very poor, almost directly mounted xenon basically the same. quite light beam condenser of some. cheap, suitable for the appearance of the person required equipment. But the model is very limited. Relatively speaking, quite many models. Brand has DEPO SYS JUNYANG etc., have made Jiuding, and Also it just goes to factory assembly, factory assembly also has a lot of German cars in Japanese car, German car, mainly with the assembly factory are basically the top with a xenon gas, but a single light a double light, double light mostly, there's also a Japanese band lens also has a single light with double light, the light effect is still good, two is better light, but not cheap, is not generally accepted prices, and some cars are more trouble ordering. There Bosch, Hella, Koito, Valeo and so on. Xenon are basically one, and this point should talk about the German FK angel eye headlights, the German FK's headlights, lighting effects are common, and this light some Taiwan manufacturers to the foundry. Modification is now popular DIY angel eyes headlights assembly, have changed the basic two-light, but the technical requirements of high personal conversion, and there are a lot of car space you, ah point of view, not right, even after sealing changed , since the change thing must be perfect Yeah, the lights have parallel tangent, but also adjustable high and low around the light, and the width of the car around and must be fit, but also suitable for high and low., lenses and light bulbs have a positive adjustment to the best condition, so in order to achieve the effect we require, so the lens is a good modification, but must be changing for the better, change is not bad, if not change it. aperture are small things, good lighting effects change can and comparable to the original car.

Detailed Angel eye headlights installed

The tools
1, oven, hair dryer, high temperature hot glue gun ÷, the word screwdriver, cutting tools, file, electric iron, electric drill; 2, LED with resistor and wire (high brightness 5000mcd above), resistor, wire; LED normally red, yellow, blue, green, purple, white, colorful, usually green light best, then white, then blue, yellow, red, colorful
How to split shade
Method one: into the oven directly to the lights inside, the set temperature of 120 degrees, and then determine the oven is not preheated, into them, heating for 5-10 minutes, the heating time due to the size of oven power varies, the general heating 4 after 5 minutes non-stop to look, and hand Baibai look more solid, then to continue to heat up to about 10-15 minutes (see the oven power, but no more than 20 minutes), you can easily hand pulled, intensity was probably something like a pencil box to open strong. If it is too long it is estimated that plastic is burned. Method Two: Using heat gun, this comparison is not terrible, but faster, is to place sealants at gunpoint to go slowly all the while to determine the glue melt open, like a lamp shade can be opened. Method three: Use hair dryer. The above two tools for people who do not, the word screwdriver stuck in the glue of the outlet, and then use hair dryer blowing, there is enough glue will melt after the temperature, and then go in with a screwdriver card, and then continue to use the hair dryer to blow into the following , walked like a blow, but more slowly. The principle is to open the lamp melted the glue, then you can, so we can melt the glue just fine as long as
Angel eyes fixed
Heat resistant transparent plastic for the angel eyes fixed on the light box, must have high temperature plastic, because some of the Amoy high with the lights higher power, continuous light after a few hours, the lamp temperature will be high, if it is ordinary plastic, glue will melt away, so that the angel eyes off, causing a lot of unnecessary trouble. After fixation, the angel eyes wide line directly connected to the lamp can be displayed. Good equipment, try light effect.
Sealed lamp
Method one, using the heating lamp on both sides of the glue gun at the side slowly, it will re-melt, put the lid closed at this time is like, and then a layer of sealant can then be double protection, I usually use the transparent temperature silicone, water-resistant sun toughness, there are many kinds of glue, unsure who to ask to find a garage like a Method two, the lamp inside the oven (no heat gun for bikers), but the sealing effect is the same, time the first set 2-3 minutes, then check the glue kept the case open the lid, into a semi-liquid when you can seal fitted out, and then add a layer of sealant just fine.  Third method is to glue the shade on the original are removed, to the best in the shade when the first split, because the glue is the best time to remove the soft, and the word with a screwdriver, glue down the fight Just take 2 times the groove, and then sealed when the sealant is to play in the original groove, and then re-packaged just fine.
Actual use
The next step is to test angel eyes the same working condition, no problem, then on loading the connection, there are problems along the above steps to re-check the dismantling of the lampshade, the connection step in accordance with the method given above should have no problem the.

prev：Car Reading Light (2011-04-06)

next：Automobile brake lights(2011-04-01)