Second-ranking ordinary stability regulator, with circuit composition, he is mainly by electronic structure, circuits, capacitance primarily, but DSP nc ballast is he is to control circuit of digital chips

Second-ranking ordinary, ballast is usually during starting current, some were about 7A can reach more than 9A and they start to stable current to 3.5 A need time is 50 seconds, due to current in 3.5 A of bulb when there was damage won't, but ordinary ballast is he needs to almost A minute time, this time will light bulb load and former car circuit effect, thus affecting the bulb life, DSP nc ballast is its starting current in only 3.9 A - 4.4 A, and they start to stable current time needed for as long as three seconds, so greatly reduced the damage and the influence of bulb

Ordinary ballast is changing Washington again when the current is light, that is current and starting badly zero began, such A back-and-forth again to light bulb and circuit are affected, and we carefully improved DSP nc ballast is with memory function, and his current is in light changing in 2.8 A, he will start from 2.8 A, which will become light bulb and former car circuit to have A better A layer of protection function

Ordinary ballast is, in itself, bulb 10V current below will appear, shem, current unstable detonation phenomenon, and our DSP nc ballast is when 8V, in current in normal work, and bulb or the amount of light has not changed, DSP nc ballast is either in high pressure or in low voltage, his constant power they can maintain 35W, constant power in stability

Second-ranking ordinary ballast is rough, walk on the road, he changes the current more big, still can appear the bulb is like, and flash nc ballast is, walking DSP on the uneven road, the current is not change, so also will the original car circuit, and bulb influential why outfit DSP anti-interference xenon lamp

Below I to illustrate several common examples:
New baolai installation hid xenon lamp common failure:

After installation of xenon lamp with flashing lights unstable, have fault code etc. Phenomenon, and, even if not bright light on market of digital technology installed sea blue star ballast is also have this case, this time, if installed ordinary xenon lamp, we're going to have to add another decoder, to solve the problems of main reason is because public car computer equipment is developed, cause easily interference, and use our DSP anti-interference, xenon lights in the 35W series, thick, thin version, all can be directly mounted version, without decoder!

Buick JunYue car hid xenon lamp installation common malfunction:

Installation will often hid xenon lamp burn out, circuit boards, Daniel is mainly the headlamps current to pass computer board to direct to the headlamps. So its requirements, and extremely low by current conventional ballast is too cold start current and start over instantly because the limits of computer board and burnt out circuit board, this car original car output current the maximum output current is at 4. 8A, and other common xenon lamp, current are in 6A, or even the lowest, 7A, also in, 5. 5A, more than the original car output current, and our DSP hid xenon lamp, his output current is in 3.9-4。9-4. 3 (A) lower than the original car output current many JunYue car, thus no longer worry installation and damage the xenon lights computer board!

Modern cool installation hid xenon lamp common fault:

Install the xenon HID lights after, start engines after opening, can appear a glowing, but engine don't start to work. Cause breakdown reason: finish installing xenon headlamps, don't launch in car engine, under the situation of xenon headlamps can normal light or become light, but a start the car engine, xenon headlamps can produce flash or out of the situation, and the instrument platform GuZhangDeng also vehicle will light up the control circuit, reason is linked by onboard computer testing, what we say usually CANBUS problems, and the working principle of xenon hid headlamps with halogen lamp and the working power of different, make the onboard computer can't detect caused by the feedback signal xenon hid headlamps. Solution: add our DSP anti-interference special hid xenon lamp, installed directly. (note: the audi A4, ford JiHu, A BMW X5 car with the same problem appear mondeo, cool and passat B5 etc part after car, installation hid xenon lamp, can appear the tome electrical equipment to light again after A power outage the phenomenon, such as mondeo will have instruments after zero restarted, passat will appear radio pause A wad phenomenon, the main cause is the ballast is caused by excessive current start-up, its current actuated by headlamps, leaving its total output requisitioned by current enough: select low current solutions, had better not start ballast is higher than the startup current 4.8 A ballast is, our DSP anti-interference stability device (starting current is in, 3. 9-4. 3A) installed directly, can!

prev：How to improve your car lights with led(2011-04-09)

next：Angel eye lamp(2011-04-07)